Sunday, April 26, 2015

Vintage radio Sonos hack


Introducing the Tandberg Sølvsuper 10 radio, a product of the Scandinavian Hi-Fi golden age. Sadly, after decades in storage, the huge variable capacitor inside has seized from corrosion and the radio was beyond repair.

So, what to do? Can this piece of 60s design be refurbished and made useful in the world of Internet of Things?

TANDBERG Sølvsuper 10, stereo for kendere


Lighting

To not mess up the original look too much I choose to keep the original front panel light bulbs, but two problems had to be tackled:

  1. The high voltage vacuum tubes had to be replaced with a modern LED array.
  2. LEDs to indicate which button was last pressed had to be fitted.

LED bar graph replaces same color radio tube

To connect a total of 22 LEDs I ended up using three 74HC595N 8-bit shift registers. The incandescent light bulbs were connected using transistors that could handle somewhat larger currents.


Rotary Encoders

I decided to keep the original logarithmic volume pots and make crude readings using AD converters. Because the pots are logarithmic, the accuracy at the lower volume levels is limited when reading using a linear ADC. I managed to get reliable readings of the values 0-10 using the Arduino built-in 10 bit ADCs.

For the tuning, bass and treble dials I wanted to use rotary encoders. I removed the mechanical wire drive connecting the tuning dial, variable capacitor and frequency display needle and connected the dial directly to a rotary encoder using a piece of wood. For the bass and treble dials I made plastic adapters that allowed the rotary encoders to fit against the back of the original pots. Then I broke of the potentiometer wipers to allow free rotation.



Original tuner dial weight and shaft removed

Stepper Motor

To drive the frequency display needle I'm using a NMB-MAT PG35L048 stepper with gearbox, that I found on eBay. I secured the stepper to the circuit board using a white metal bar from some old IKEA drapes. The original wheel fit on the stepper shaft using a piece of cardboard as a spacer.


Snortrekk diagram from the TANDBERG Sølvsuper 10 service manual



Mainboard

To make sure that there is no lag when operating the front panel dials and buttons, most user input is detected using interrupts and the stepper and speaker is driven using timers. I choose to use two Arduinos because of the number of interrupts required and because I need quite a lot of real estate given my limited soldering skills. Here's how the hardware was connected:

  • Front panel buttons connect to Arduino Mega using interrupts PCINT17-23.
  • Tuning dial rotary encoder connects to Arduino Mega, using interrupts INT5 and PCINT16. Rotary encoder push button connects to D13 using interrupt PCINT17.
  • IR and RF receiver connects to Arduino Mega using interrupts INT4 and INT2.
  • Ethernet board connects to Arduino Mega.
  • Bass and treble dial rotary encoders connect to Arduino Uno using interrupts INT0, INT1, PCINT10 and PCINT20.
  • Stepper connects to Arduino Uno using Timer 2 for stepping.
  • Speaker connects to Arduino Uno using Timer 2 for tone generation.
  • LEDs and light bulbs connect to Arduino Uno and are dimmable using PWM.

Sensor and RTC clock headers and 434MHz RF receiver daughter board



Ethernet and USB

The intertubes would not be possible were it not for the RJ45 jack. In addition to an Ethernet connector I added a back panel USB socket and a reset button for convenience.


USB, Ethernet and recessed reset button in original back panel

9 comments :

  1. Utrolig bra! Jeg har selv Sonos og har nylig fått meg en Huldra 8! Er dette prosjektet mulig å få til uten å være profesjonell og ved hjelp av din bruksanvisning? Videre, du nevner Arduino, er dette DIY-elektronikk sett/styringssystemer? Kanskje en DAB-fiks hadde vært greie også? Du har kanskje en slik løsning også?

    ReplyDelete
    Replies
    1. Med vilje og pågangsmot kommer man langt, jeg er selvlært hobbyelektroniker :) Arduino er en mikrokontrollerplattform for hobbyelektronikere med en stor «community» og masse litteratur. Man kunne helt sikkert laget noe for DAB også, men jeg har ingen slik løsning dessverre.

      Delete
  2. Konge prosjekt! Planlegger å ta for meg et gammelt sølvsuper radioskap etter nyttår. Har du lagt ut kildekoden din noe sted? Planlegger å bruke mye av de samme teknikkene du har brukt for å ta i bruk de gamle kontrollene og hadde satt veldig pris på om du ville delt litt av koden din.

    ReplyDelete
  3. Jeg er mektig imponert! Jeg har selv benyttet grammofoninngangene på gamle Tandberg-modeller (så godt som samtlige gamle vakuumrørradioer har dette) som tilkobling for Chromecast Audio eller mobiltelefon. Dette funker utmerket dersom forsterker-biten av radioen fortsatt fungerer, og det gjør de jo som oftest :)

    ReplyDelete
  4. The work changed into very thoughtfully achieved and you could tell how thorough and professional the task becomes.

    ReplyDelete
  5. - PRNGs use a set of statistical recommendations norges cåsino referred to as an algorithm to get an enormous circulation of amounts that give the sense of correct randomness.

    ReplyDelete
  6. Fantastisk flott radio. Hvor mye tid å evt ca pris har det kommet på?
    Kunne tenke meg å gjøre det samme med min radio

    ReplyDelete
  7. I would exceptionally endorse his services preferred contracting desires. web design firms for ad agencies

    ReplyDelete
  8. Upcoming on-line casino gaming laws are also anticipated to have a strong impression on the market; nonetheless, this will differ strongly by 카지노 region. As such, many social casino gaming companies are diversifying their portfolio to counter an over-reliance on their playing segments. Enjoy all your favourite games in our 86,000-square-foot casino. Play your fortunate Keno numbers, wager your favorites in the spacious race and sports activities e-book or head upstairs to our lavish 720-seat bingo room.

    ReplyDelete